We specialize in hard to find items
(1)
4PCs Replacement Analog Joystick for Xbox One Controller – ElecGear Repair Parts 3D Thumb stick Wireless Controller Rocker with T6 T8 Screwdriver Tool Kit for Xbox One, One S, One X and Elite
Share Tweet
*Price and Stocks may change without prior notice
*Packaging of actual item may differ from photo shown
- Electrical items MAY be 110 volts.
- 7 Day Return Policy
- All products are genuine and original
- Cash On Delivery/Cash Upon Pickup Available
4PCs Replacement Analog Joystick for Xbox One Features
-
[EL4 for Xbox Controller] – 4x replacement analog joystick widely compatible with Xbox wireless controllers: Xbox One, One S and X and Elite Series 1. It is also used in newest Xbox Series S|X controllers. The thumbstick module was made by ALPS. This RKJXV stick controller series comes with 10K ohm trimmer potentiometers
-
[Compatibility] – This version of analog stick comes in light gray bottom plate. It locks in certain direction when not sit in controller cover. It comes with the same 14 prongs structure as PS4 versions. However, they’re slightly different from each other. Please use this EL4 for Xbox. Be noticed: EL4 does not work with older Xbox 360
-
[Additional Resistor] – Complicated moving mechanism and daily wear and tear finally caused drifting. Even new sensors cannot be 100% balanced. Calibrating in controller settings might not work. We packed 10x correction resistors to solve the potential problem in hardware level. Solder one or two paralleled tiny resistors onto the potentiometer at the opposite direction against drifting. It will help correct 3 to 5 degrees drifting
-
[When to replace] – The analog joystick needs to be replaced when your controller has the problem of drifting, creeping, stuttering, a blind spot, a dead spot, a dead zone, no reaction when clicking, or it wouldn't center after years of wear and tear. The OEM genuine repair parts ensure accuracy and prolong lifespan
-
[Reminder of DIY] – With as many as 14 prongs, de-soldering and soldering the whole module takes serious skills. We suggest replacing the potentiometers first to solve most of the joystick problems. To desolder the entire joystick module off PCB by a normal soldering iron, please take a look at the desoldering kit at product ID: B0BK7169M8
About 4PCs Replacement Analog Joystick For Xbox One
Please take a look at product ID: B0BK7169M8 for the desoldering kit, and B0BGPCCYH8 for solving drifting problem EL4 compatible with Xbox Controller 4x replacement analog joystick widely compatible with Xbox wireless controllers: Xbox One, One S and X and Elite Series 1. It is also used in newest Xbox Series S|X controllers. The thumbstick module was made by ALPS. It belongs to RKJXV stick controller series. It comes with 10KΩ trimmer potentiometers. This version of analog stick comes in light gray bottom plate. It locks in certain direction when not sit in controller cover. It comes with the same 14 prongs structure as PS4 versions. However, they’re slightly different from each other ✔ Replace the wiper alone even without soldering In some cases, you can just replace the wheel in the potentiometer to solve specific problems like: Stuttering, dead zone, creeping, or not as responsive as it should be ✔ Replace the potentiometer alone with an iron 80% chances of joystick problem are caused by the sensor. In another words, the rotary mechanism and the tactile switches are not the problem. De-soldering the unit with only 3Pin can be easier than replacing the entire module with as many as 14 prongs ✔ A heat gun to replace the whole module This is the most suggested for an experienced soldering expert ✔ Experts with a normal iron to replace the whole unit For a soldering expert with no professional de-soldering wick braid, solder sucker pump or hot air rework station at hand. To make it easy, we suggest crushing the problem joystick into small enough pieces with a pair of pliers ✔ By professional technicians in a cellphone repair shop Suggested for someone with no handy tools
