We specialize in hard to find items
All Categories
SANIFLO Saniplus Macerator Pump - 1/2 HP - Residential & Commercial
Share Tweet
*Price and Stocks may change without prior notice
*Packaging of actual item may differ from photo shown
- Electrical items MAY be 110 volts.
- 7 Day Return Policy
- All products are genuine and original
SANIFLO Saniplus Macerator Pump - 1/2 HP Features
-
BONUS FULL BATH: Saniplus is a 1/2 HP pump system used to install a complete bathroom up to 15 feet below the sewer line, or even up to 150 feet away from a soil stack. For residential use only.
-
DUAL PURPOSE: Will also discharge gray water from any sink, bath/shower or urinal. The wastewater will drain into the system on either side of the housing.
-
COMPATIBLE MODELS: This pump can only be connected to Saniflo’s 1.28 GPF/4.8 LPF rear discharge toilet which come in round and elongated models.
-
TECHNICAL SPECIFICATIONS: Noise level: ≤ 53 dBA (Lp) (measured at 3 ft.); Discharge rate at 15 ft: 17 GPM; Shut-off head: 30 ft; Certification code: CSA (IPC, NSPC), IAPMO (UPC); Connections: Rear outlet toilet, sink, shower/bathtub
-
4 YEAR WARRANTY: All of Saniflo's products have a 2 year warranty with purchase, and an additional 2 years is added with registration. Our warranty program can offer peace of mind, should a problem arise.
About SANIFLO Saniplus Macerator Pump - 1/2 HP
Product Description Saniflo is the world leader in the plumbing industry as a result of the above-floor technology used in Saniflo pumps. Saniflo has a complete range of pumps for both residential and commercial needs. The innovative method of using above-floor technology allows for the installation of any sanitary application you can imagine, anywhere! Whether it's a small project requiring drain and condensate pumps to more complex engineered jobs such as whole buildings with multiple fixture units, Saniflo has a solution; All you need is water supply and electricity. From the Manufacturer The SANIPLUS is a system used to install a complete bathroom up to 15-Feet below the sewer line, or even up to 150-Feet away from a soil stack. It can handle the effluent from a toilet, sink, bathtub and shower. It offers a high level of styling that makes it the ideal centerpiece for a modern bathroom. The inside of the SANIPLUS is comprised of a pressure chamber, which starts and stops the unit, and the motor, which drives the stainless steel macerator blades and the pump. The unit pumps the effluent upward 15-Feet and/or 150 horizontally (with gravity fall). Once the water level in the container goes down, the micro switch deactivates the unit until the flush is activated again. A normal operating cycle for SANIPLUS takes about 7-9 seconds. In addition to the toilet waste, the SANIPLUS with also discharge gray water from a variety of other sanitary fixtures such as: a sink, a bathtub, a shower and a urinal. When adding a bathtub or shower, a base will have to be constructed. This base should be made out of a 2-Inch X 6-Inch(minimum) or 2-Inch X 8-Inch(recommended) on edge, to allow for the installation of a P-trap and the required 1/4-Inch per foot gravity flow towards the pump unit. The wastewater from other sanitary fixtures is discharged into the SANIPLUS via two 2-Inch inlets on either side of the housing. Either one or both inlets can be used as required. The discharge elbow on top of the SANIPLUS can be turned either to the left, to the right, or towards the back, depending on the discharge installation. A non-return valve, which comes already assembled on the discharge elbow, prevents back flow into the unit. This unit has been designed with a vent connection on the lid. All plumbing codes require connection to a vent system. Please note that the vent system should be a two-way air vent. The use of mechanical vents, air admittance valves, or similar devices is not permitted as these are considered one-way air vent systems.
