We specialize in hard to find items
All Categories
4 x POTS RJ11 Telephone and Gigabit Ethernet Over Fiber Converter - Multiplexer - Extender Set of FXS FXO Units - Universal Single and Multimode - 1 km MM (0.6 mi) 20km SM (11.4 mi) - Voice Over Fiber
Share Tweet
*Price and Stocks may change without prior notice
*Packaging of actual item may differ from photo shown
- Electrical items MAY be 110 volts.
- 7 Day Return Policy
- All products are genuine and original
4 x POTS RJ11 Telephone and Gigabit Ethernet Over Features
-
Protect Your Home: Bulletproof Phone to Fiber fiber cable extender for long, prone to lightning, lengthy outdoor copper cables + Gigabit Ethernet connection will over SAME fiber along with 4 phones!
-
Universal for Both Fiber Types: Same media converter (extender) supports Multimode fiber for a distance up to 1 km (0.62 miles) and Single mode fiber for a distance up to 20 km (11.42 miles), wavelength 1300/1310 nm
-
Extend your Phones (even Fax Supported!) & Network: 4 Independent FXS / FXO Telephone or Fax lines + 1 GIGABIT (!) Ethernet (10/100/1000 Mbit/s) Autosensing port over same Multimode or Single mode fiber cable
-
Plug & Play and Simple to Install: No setup or configuration needed, SC connector for fiber optical port, RJ-11 connector for telephone ports & RJ-45 for Gigabit Ethernet 10/100/1000Mbit/s
-
No Delay Transmission & Protocol Support: Unlike VoIP products - these converters transmit signals directly over fiber cables, thus offering NO DELAYS, plus support for FAX & Legacy applications that is not supported by VoIP lines
About 4 X POTS RJ11 Telephone And Gigabit Ethernet Over
AD-net’s AN-FM-PCM02/GETH-M Fiber Optic Multiplexers offer a low-cost solution for extending limited reach POTS RJ-11 copper telephone lines to fiber optical distances of over 11.4 miles using Single Mode - SM type optical fibers and 0.62 miles using Multimode (Multi Mode - MM) fibers. Besides extending 4 telephone lines over the same fiber, these multiplexers also carry 1 Gigabit Autosensing Ethernet RJ-45 network port, which offers even more effective re-use of fiber cables. Even more importantly, – besides the extension, which more often than not, happens outdoors, AD-net’s Phone over Fiber extenders solves the problem of lighting protection for your home. Lengthy copper cables, installed outdoors, are prone to attracting lightning, and this can damage electrical equipment in your homes. Technical Specifications Telephone Ports Physical interface: RJ11 Voice Bandwidth: 8KHZ Codec method: PCM codec Signaling: Transparent support any in-band signaling, including calling number detection Connection type: PABX (FXO) side to Phone (FXS) side FXS: Ringing voltage: 75V, ringing frequency: 25HZ FXO: Two-wire input impedance: 600Ω (off-hook) Return loss: 40 db, ringing detection voltage: 35V Ring detection frequency: 17HZ-60HZ Return loss: 40 db Fiber Optical Interface Optical wavelength: 1310nm Fiber: multimode mode (MM) or single mode (SM) Transmission range: 1km for MM or 20km for SM Optical interface: SC duplex UPC/PC (blue) (2 fibers needed) Ethernet interface Datarate: 10/100/1000Mbps - Gigabit Ethernet Connector: RJ45 General Specifications Voltage: AC 90 - 260 AC, US type Power Plug Power Consumption: ≤5W Working temperature: -10°C ~ 60°C Storage temperature: -35°C~+70°C Relative humidity: 95 %
