DROK DC Buck Module, Adjustable Buck Converter Step Down Voltage Regulator 6V-32V 30V 24V 12V to 1.5-32V 5V 5A LCD Power Supply Volt Reducer Transformer Module Board with USB Port Protective Case

Product ID : 39195070

Available options (color, size, package, etc). Prices may vary.

---

  Share   Tweet

share more:

---

Galleon Product ID 39195070

Shipping Weight 0.15 lbs
I think this is wrong?

Model 180080AFA

Manufacturer DROK

Shipping Dimension 5.24 x 3.03 x 1.97 inches
I think this is wrong?

See more product information!

-

Save 11%

Before ₱ 1,595

₱ 1,415

Price Tracker

+ ₱ 150
International Shipping

via AIR

Get it between 2024-12-30 to 2025-01-06. Additional 3 business days for provincial shipping.

---

BUY NOW!

*Price and Stocks may change without prior notice
*Packaging of actual item may differ from photo shown

---

• Electrical items MAY be 110 volts.
• 7 Day Return Policy
• All products are genuine and original
• Cash On Delivery/Cash Upon Pickup Available

Pay with

DROK DC Buck Module, Adjustable Buck Converter Step Features

• PARAMETER --- Input voltage range DC 6V-32V; Output voltage DC 1.5V-32V; Max output current 5A, recommend use of within 4.5A; Max output power 75W, recommend use of within 50W.

• GENERAL USE --- As ordinary step-down module with over-current protection; As constant current LED driver module; DIY a solar power controller, etc.

• DISPLAY --- Large clear digital LCD display voltage & current value simultaneously.

• FEATURES --- Constant current/voltage mode; Voltage calibration & current calibration; USB interface; Protective case; Short-circuit protection; Over-temperature protection; Input reverse connection protection.

• NOTE --- 1). Output voltage is set as around 20V by default, if your input is lower than that, please turn potentiometer anticlockwise for 10 laps or more until voltage changes. 2). The case is packaged unassembled to avoid damage during transit. It needs to be manually installed. 3). Please carefully read the user’s manual, especially the “Cautions” before using. You can find the PDF Instructions on this page -- Product information -- Product guides and documents -- User Manual [PDF].

About DROK DC Buck Module, Adjustable Buck Converter Step

Parameters： Chip: MP2304 Input voltage: 6~32V Output voltage: 1.5~32V continuously adjustable (Input should be 1.5V higher than output.) Output current: 5A max, adjustable, recommended use within 4.5A. (Over 3A or 35W, please enhance heat dissipation.) Constant current requires an output voltage of above 2V to be adjusted. Current regulation can only be performed in the status of constant current. Output Power: 75W (max), recommended use within 50W. Please reduce the power when voltage difference is large. Operating temperature: -20℃ to +70℃ Operating frequency: 180KHz Conversion efficiency: up to 96% Short circuit protection: Yes (Constant current value set by constant current function) Over-temperature protection: Yes (Automatically shut off the output when overtemp.) Input reverse polarity protection: Yes Output backflow prevention: None. Please add a diode when used for charging. Installation: 8x pillars, 8x 3mm screws Wire Connection: terminal block or soldering terminals; VIN is input; VOUT is output. Dimension: 65.6*40*25mm Display Modes: 1). F-0 mode: Display output voltage 2). F-1 mode: Display input voltage 3). F-2 mode: Display input and output voltage alternately 4). USB mode: Display USB output voltage & turn on/off USB output Note: Output is set as around 20V before leaving factory, if your input is lower than that, please turn potentiometer anticlockwise for at least 10 laps until voltage changes. Package Included: 1x DC Buck Module 4x Copper Cylinder Screws M3*6 4x Double-pass Screws M3*12 8x Roundhead Screws M3*6