HEATIT Pipe Heating Cable - Reliable Freeze Prevention, Easy DIY Install, Durable Design for Water Pipes CSA & ETL Certified, Energy-Efficient Water Pipe Heat Cable HISD 9ft, 7w/ft, 120V

Pay with

HEATIT Pipe Heating Cable - Reliable Freeze Features

• Choose safety first with our CSA and ETL certified constant wattage pipe heating cable. These certifications guarantee top-notch safety standards. Protect your pipes and equipment from overheating and short circuits while reducing fire risks. Count on us for high-quality, certified solutions. Buy now for peace of mind.

• 𝙐𝙨𝙚 𝙛𝙤𝙧 𝙬𝙖𝙩𝙚𝙧 𝙛𝙞𝙡𝙡𝙚𝙙 𝙥𝙡𝙖𝙨𝙩𝙞𝙘 (𝙞𝙣𝙘𝙡𝙪𝙙𝙞𝙣𝙜 𝙋𝙀𝙓) 𝙤𝙧 𝙢𝙚𝙩𝙖𝙡 𝙥𝙞𝙥𝙚𝙨. 𝙉𝙤𝙩 𝙪𝙨𝙚 𝙛𝙤𝙧 𝙖𝙣𝙮𝙩𝙝𝙞𝙣𝙜 𝙚𝙡𝙨𝙚, 𝙡𝙞𝙠𝙚 𝙚𝙢𝙥𝙩𝙮 𝙬𝙖𝙩𝙚𝙧 𝙥𝙞𝙥𝙚𝙨, 𝙛𝙪𝙚𝙡 𝙡𝙞𝙣𝙚𝙨, 𝙝𝙤𝙨𝙚𝙨, 𝙜𝙪𝙩𝙩𝙚𝙧𝙨, 𝙨𝙩𝙚𝙖𝙢 𝙡𝙞𝙣𝙚𝙨 𝙖𝙣𝙙 𝙨𝙤 𝙤𝙣. Two-year limited quality . If you are not completely satisfied with HEATIT heating cable, please don't hesitate to contact our customer service at any time, we'll try our best to solve your issues.

• Pre-assembled easy to install. Including grounded plug with light, built in thermostat, and instructions. Easy to install and use. 120 volt, 7 watts/ft. Built in thermostat to turn the cable 37F on 50F off. Energy saving. 100% screen rate with the Aluminum foil and tinned copper braid. Industrial grade heat shrinkage tube for connection. Tough XLPE as inner insulation and weather resistant PVC (high-low temperature) as out jacket.

• Maximum 1/2 in fiberglass insulation was used over the heating cable for lower temperature protection. Pipes must be at least 3 feet and at least 3/8'' and less than 1 1/2'' in. diameter. No crossing. No spiral. No overlap itself. Only straight. This product is backed by up to USD 2 million in product liability insurance, providing you with added peace of mind and security in your purchase.

• Testing the cable before the installation. Uncoil the cable, plug in the heat tape for water pipes and then put the thermostat part of the cable into an ice bucket for few minutes. When the temperature is below 37F, the thermostat will energize the cable to work. Normally you can feel the slight warm on the heating cable in few minutes. To avoid the overheat, please don't plug in the cable for a long time for testing. When you feel the slight warm, please turn it off.

About HEATIT Pipe Heating Cable - Reliable Freeze

Why can HISD pipe heating cable give you a safe, healthy energy saving and durable water pipe? The plug of HISD owned the indication light to show you whether there is electricity or not. With the build in thermostat, you can save more energy. HISD pipe heating cable was approved by both CSA and ETL. You can have more confidence on the product safety. Pre-assemble pipe heating cable make installation easy for do-it-yourselfers. HISD owned the aluminum foil and the tinned copper braid to make sure the 100% screen rate to make the product more healthy and more stable. In the connection, HISD take the industrial grade heat shrinkage tube technology to make the cable more durable. How about the manufacturer? The factory meet ISO9001 standard (audit by BV)in the production process and the company take a very strict requirement on the incoming material, production process control, finish good inspection etc. Advanced product structure engineering design, good raw material, strict production process, strict internal management plus many years maneuvering experience make HISD more reliable. Application tips The HISD is pre-assemble and easy to install, protect the pipe diameters up to 1.5" from freezing. You can choose different lengths based on the chart in the instruction. Warning Never allow heating cable to touch, cross or overlap itself at any points. No crossing. No spiraling. Never install heating cable on plastic pipe unless pipe is filled with water all the times. Do not install the same cable on more than one pipe. While it is coiled, never plug in the heating cable. Never alter this heating cable in any way. The thermostat and the entire heating cable has to be in contact with the pipe. Combustible material must not be within 1/2 in. of completed installation. Never use metal binding to secure heating cable to pipe.